Mapping the Nanoscale Architecture of Functional Materials

Zoom in to the micro or nanostructure of functional materials, both natural and manmade, and you’ll find they consist of thousands upon thousands of coherent domains or grains - distinct regions where molecules and atoms are arranged in a repeating pattern. 

Such local ordering is inextricably linked to the material properties. The size, orientation, and distribution of grains can make the difference between a sturdy brick or a crumbling stone; it determines the ductility of metal, the efficiency of electron transfer in a semiconductor, or the thermal conductivity of ceramics. It is also an important feature of biological materials: collagen fibres, for example, are formed from a network of fibrils and their organisation determines the biomechanical performance of connective tissue. 

These domains are often tiny: tens of nanometres in size. And it is their arrangement in three-dimensions over extended volumes that is property-determining. Yet until now, techniques to probe the organisation of materials at the nanoscale have largely been confined to two-dimensions or are destructive in nature. 

Now, using X-rays generated by the Swiss Light Source SLS, a collaborative team of researchers from Paul Scherrer Institute PSI, ETH Zurich, the University of Oxford and the Max Plank Institute for Chemical Physics of Solids have succeeded in creating an imaging technique to access this information in three-dimensions.

“We not only look inside, but with nanoscale resolution” 

Their technique is known as X-ray linear dichroic orientation tomography, or XL-DOT for short.  XL-DOT uses polarised X-rays from the Swiss Light Source SLS, to probe how materials absorb X-rays differently depending on the orientation of structural domains inside. By changing the polarisation of the X-rays, while rotating the sample to capture images from different angles, the technique creates a three-dimensional map revealing the internal organisation of the material.

The team applied their method to a chunk of vanadium pentoxide catalyst about one micron in diameter, used in the production of sulfuric acid. Here, they could identify minute details in the catalyst`s structure including crystalline grains, boundaries where grains meet, and changes in the crystal orientation. They also identified topological defects in the catalyst. Such features directly affect the activity and stability of catalysts, so knowledge of this structure is crucial in optimising performance.

Importantly, the method achieves high spatial resolution. Because X-rays have a short wavelength, the method can resolve structures just tens of nanometres in size, aligning with the sizes of features such as the crystalline grains. 

“Linear dichroism has been used to measure anisotropies in materials for many years, but this is the first time it has been extended to 3D. We not only look inside, but with nanoscale resolution,” says Valerio Scagnoli, Senior Scientist in the Mesoscopic Systems, a joint group between PSI and ETH Zurich. “This means that we now have access to information that was not previously visible, and we can achieve this in small but representative samples, several micrometres in size.”

Leading the way with coherent X-rays

Although the researchers first had the idea for XL-DOT in 2019, it would take another five years to put it into practice. Together with complex experimental requirements, a major hurdle was extracting the three-dimensional map of crystal orientations from terabytes of raw data. This mathematical puzzle was overcome with the development of a dedicated reconstruction algorithm by Andreas Apseros, first author of the study, during his doctoral studies at PSI, funded by the Swiss National Science Foundation (SNSF).

The researchers believe that their success in developing XL-DOT is in part thanks to the long-term commitment to developing expertise with coherent X-rays at PSI, which led to unprecedented control and instrument stability at the coherent Small Angle X-ray Scattering (cSAXS) beamline: critical for the delicate measurements. 

This is an area that is set to leap forwards after the SLS 2.0 upgrade: “Coherence is where we’re really set to gain with the upgrade,” says Apseros. “We’re looking at very weak signals, so with more coherent photons, we’ll have more signal and can either go to more difficult materials or higher spatial resolution.”

A way into the microstructure of diverse materials

Given the non-destructive nature of XL-DOT, the researchers foresee operando investigations of systems such as batteries as well as catalysts. “Catalyst bodies and cathode particles in batteries are typically between ten and fifty micrometres in size, so this is a reasonable next step,” says Johannes Ihli, formerly of cSAXS and currently at the University of Oxford, who led the study.

Yet the new technique is not just useful for catalysts, the researchers emphasise. It is useful for all types of materials that exhibit ordered microstructures, whether biological tissues or advanced materials for information technology or energy storage. 

Indeed, for the research team, the scientific motivation lies with probing the three-dimensional magnetic organisation of materials. An example is the orientation of magnetic moments within antiferromagnetic materials. Here, the magnetic moments are aligned in alternating directions when going from atom to atom. Such materials maintain no net magnetisation when measured at a distance, yet they do possess local order in the magnetic structure, a fact that is appealing for technological applications such as faster and more efficient data processing. “Our method is one of the only ways to probe this orientation,” says Claire Donnelly, group leader Max Planck Institute for Chemical Physics of Solids in Dresden who, since carrying out her doctoral work in the Mesoscopic Systems group has maintained a strong collaboration with the team at PSI. 

It was during this doctoral work that Donnelly together with the same team at PSI published in Nature a method to carry out magnetic tomography using circularly polarised X-rays (in contrast to XL-DOT, which uses linearly polarised X-rays). This has since been implemented in synchrotrons around the world. 

With the groundwork for XL-DOT laid, the team hope that it will, in a similar way to its circularly polarised sibling, become a widely used technique at synchrotrons. Given the much wider range of samples that XL-DOT is relevant to and the importance of structural ordering to material performance, the impact of this latest method may be expected to be even greater. “Now that we’ve overcome many of the challenges, other beamlines can implement the technique. And we can help them to do it,” adds Donnelly. 

Read the original article on Paul Scherrer Institute (PSI).